
Chimney, valley, wall and boot flashing — renewed with new metal
Roof flashing repair Dallas TX that stops the leak at its source
Flashing is the metal that keeps water out where the roof changes direction — at chimneys, walls, valleys, skylights and vent pipes. It is the part of the roof that fails most often and is noticed least, because it sits under the shingles and only shows itself when it leaks. We renew failed flashing with new metal, lapped so the water runs over the joint, and check the decking the leak has already wet.
What's included
What flashing repair includes
A roof flashing repair in Dallas is a diagnosis and a renewal in that order. The scope covers the attic inspection, the failed detail, the new metal, and the decking the leak has already wet.
Step flashing renewed
Chimney and wall step flashing are renewed with new metal, woven into the courses one piece at a time, so each piece laps correctly over the one below it.
Counter flashing re-set
Counter flashing that has pulled away from the brick is re-set and sealed at the joints, so the water runs over the step flashing and not behind it.
Valley metal replaced
Split valley liners are replaced with new valley metal, and the shingles are re-cut along both edges, so the water channel carries the water again.
Pipe boots replaced
Cracked rubber pipe boots are replaced with new boots and new flashing around them, and the shingles around them are checked for the same age.
Decking checked under it
The decking under the failed flashing is checked for wetness and softness, so the repair covers the damage the water caused, not just the metal that failed.
Documented throughout
Photos of the failed detail, the attic path, and the finished repair, so you can see what the leak was and what fixed it.
Service overview
What roof flashing repair in Dallas actually involves
Roof flashing repair in Dallas is the renewal of the metal details that keep water out of a roof: step flashing at chimneys and walls, valley liners, counter flashing, and pipe boots. The repair is to replace the failed metal with new metal, woven into the surrounding courses, so the water runs over the joint instead of into the house.
Flashing is the metal that keeps water out where the roof changes direction — at chimneys, walls, valleys, skylights and vent pipes. It is the part of the roof that fails most often and is noticed least, because it sits under the shingles and only shows itself when it leaks. Most repeat leaks in Dallas trace to flashing: a step flashing that was never renewed, a counter flashing that pulled away from the brick, a valley liner that split, or a pipe boot that cracked in the sun. The repair is to replace the failed metal with new metal, lapped so the water runs over the joint.
The service timeline
What to expect during your flashing repair
The order is the same on every flashing job, whatever the detail.
Attic first
We look at the decking and the insulation from inside, following the stain to the highest point the water reaches. That is where the roof above it gets checked.
Roof second
The roof above the attic stain is walked and checked by hand — chimney, valley, wall, skylight and vent flashing — until the failed detail is found and photographed.
Scope
The written scope names the failed detail, the new metal that will replace it, and any decking the water has damaged. If the roof around it is failing too, the scope says so.
Repair
The failed flashing is replaced with new metal, lapped so the water runs over the joint, and woven into the surrounding courses. The repair is photographed from the roof and from the attic where access allows.
Cleanup and walkthrough
Debris collected, tarps folded, and a magnet sweep below the work area. The photos of the repair and the failed detail are shown to you before we leave.
Tools & methods
Tools and methods we use on your flashing
Flashing tools are for cutting and folding metal — the detail is made to fit, not forced into place.
Tin snips and brake
Cuts and folds new flashing to fit each chimney, wall and valley exactly, instead of forcing a stock piece into place.
Pry bar and shingle remover
Lifts the courses over the failed flashing without tearing the good shingles around them, so the repair weaves in cleanly.
Moisture meter
Finds the wet decking the leak has caused, so the repair covers the damage, not just the flashing.
Sealant
Seals the joints where the detail calls for it — at counter flashing, laps and terminations — never as a substitute for new metal.
Roofing nail gun
Fastens the replacement shingles at the manufacturer's pattern and depth, so the repair holds in a 115 mph design wind.
Step flashing stock
Cuts step flashing pieces to fit each course, so every shingle has its own flashing piece lapped correctly.
Use cases
When Dallas homeowners call us about flashing
These examples show how a flashing repair is scoped to the detail that failed.

Valley liner in Lower Greenville
A stain at the joint of two ceiling planes, worst in heavy rain. The valley liner had split where the two slopes meet. New valley metal, shingles re-cut along both edges, and the attic decking dried and checked.
Skylight curb in the M-Streets
A stain at the skylight curb that only showed in wind-driven rain. The curb flashing had never been renewed and the counter flashing had pulled away from the frame. New curb flashing, sealed at the joints, and the decking around the skylight checked for wetness.
Problems we solve
Problems flashing repair solves for Dallas homes
Most flashing calls are one of these four. Each one starts with the same question: which detail failed?
Leak at the chimney
We renew the step flashing and the counter flashing with new metal, sealed at the joints, and check the attic for the wet decking the leak has caused.
Leak in the valley
We lift the shingles along the valley, lay new valley metal, and re-cut the shingles along both edges, so the water channel carries the water again.
Drip at a vent pipe
A cracked pipe boot is replaced with a new boot and new flashing around it, and the shingles around it are checked for the same age.
Leak that came back after a repair
A repair that replaced the shingle but left the old flashing in place will be back. We re-diagnose from the attic and the roof until the real failed detail is found.
Cost factors
What shapes the cost of flashing repair in Dallas
WHICH DETAIL FAILED, AND WHAT IT HAS DAMAGED
Which detail failed
A pipe boot is a small job. A chimney flashing replacement is a bigger one. The scope names the detail, so the price follows the work.
Decking around it
If the decking under the failed flashing is wet or soft, it is part of the repair. The scope covers the wet decking, not just the metal that failed.
Access and pitch
A flashing repair on a low, walkable slope is straightforward. Height and pitch change the job — steep slopes and two-story work need more fall protection and more time.
Customer reviews
What Dallas customers say about our flashing work
“I hired a roofing and exterior crew to replace the fascia, corner trim, gutters, and the front siding on my home. The work turned out excellent, and the whole project was handled with real care.”
Why do roof leaks keep coming back?
Most repeat leaks trace to flashing: chimney step flashing, wall flashing, valley metal, and pipe boots. A repair that replaces the shingle but leaves the old flashing in place is a repair that will be back. The inspection finds the failed detail, and the repair renews it with new metal.
How much does flashing repair cost in Dallas?
It depends on which detail failed — a pipe boot is a small job, a chimney flashing replacement is a bigger one — and on the condition of the decking and shingles around it. The quote follows the inspection, and it is itemised for the flashing repair as scoped.
My chimney leaks — is it the flashing or the chimney?
A chimney leak is usually a flashing leak, not a masonry leak. The step flashing and the counter flashing are the two pieces that keep water out where the chimney meets the roof, and both are renewed with new metal, sealed at the joints, and checked from the attic for wet decking.
Can a valley leak be repaired without replacing the roof?
Yes. A valley is a water channel, and the liner is the metal that carries the water. When the liner splits, the water runs under the shingles and into the house. The repair is to lift the shingles along the valley, lay new valley metal, and re-cut the shingles along both edges.
Ready when you are
Get your roof flashing repair Dallas TX quote
An inspection, photos, and an itemised written quote for the flashing repair as scoped. Call (469) 960-7533 and tell us where the water shows up.

Talk with the local team
Request Roof Flashing Repair
Call us at (469) 960-7533 or send a message and we will get back to you. We are open 24 hours, every day. Tell us where the leak shows up and when, and we will give you a straight answer on what it needs.




