
Rotted boards cut out, new timber fitted, gutters re-hung
Soffit and Fascia Repair Dallas TX | Fonseca Brothers Roofing
Fascia is the board at the edge of the roof that the gutters hang from, and soffit is the underside of the eave that closes the gap between the wall and the roof. Both rot when they stay wet — from a gutter that overflows, a roof edge that leaks, or a soffit vent that has been blocked for years. We cut out the rotted board and replace it with new timber, primed and painted, with the gutters re-hung to the new fascia and the soffit vents opened so the air can move.
What's included
What soffit and fascia repair includes
A soffit and fascia repair in Dallas is a carpentry job and a roofing job together: the rot cut out, the new timber fitted, the gutters re-hung, and the soffit vents opened. The scope is written down before the work starts.
Rot cut out, not painted over
The rotted board is cut out and replaced with new timber, primed and painted. A fascia that is painted over without cutting out the rot will rot again.
New timber, primed and painted
The replacement board is new timber, primed and painted, so the repair lasts and the paint holds. The joints are sealed where the detail calls for it.
Gutters re-hung to the new fascia
Gutters hang from the fascia, and when the fascia is replaced the gutters are re-hung to the new board. A gutter hung to a bad board will pull away again.
Soffit vents opened
Soffit vents that are painted shut or blocked are opened and cleared, and the baffles are checked, so the air can move through the attic.
Cause fixed, not just the board
The gutter or the roof edge that kept the fascia wet is fixed as part of the job, so the new board does not rot the same way.
Documented throughout
Photos of the rot, the new timber, and the finished eave, so you can see what the repair was and what it is now.
Service overview
What soffit and fascia repair in Dallas actually involves
Soffit and fascia repair in Dallas is the replacement of rotted timber at the eaves of a roof: the fascia board that the gutters hang from, and the soffit that closes the underside of the eave. The repair is to cut out the rot and fit new timber, primed and painted, and to fix the gutter or the roof edge that kept it wet — because a fascia that is painted over without cutting out the rot will rot again.
Fascia is the board at the edge of the roof that the gutters hang from, and soffit is the underside of the eave that closes the gap between the wall and the roof. Both are timber in most Dallas homes, and both rot when they stay wet — from a gutter that overflows, a roof edge that leaks, or a soffit vent that has been blocked for years. The repair is to cut out the rotted board and replace it with new timber, primed and painted, with the gutters re-hung to the new fascia and the soffit vents opened so the air can move. A fascia repair that is painted over without cutting out the rot is a repair that will be back.
The service timeline
What to expect during your soffit and fascia repair
The order is the same on every soffit and fascia job, whatever the eave.
Inspection
We look at the eaves from the ground and from the ladder, checking the fascia, the soffit, the gutters and the roof edge. You get photos of what we find and a straight answer on how much board is rotted.
Scope
The written scope names the board to replace, the gutters to re-hang, and the soffit vents to open, so the job is agreed before anything is cut out.
Cut out and replace
The rotted board is cut out and replaced with new timber, primed and painted, and the joints are sealed. The repair is photographed before the paint goes on.
Re-hang and open
The gutters are re-hung to the new fascia, the soffit vents are opened and the baffles are checked, so the air can move through the attic.
Cleanup and walkthrough
Debris collected, the ground swept, and a walk of the eaves with you. You see the photos of the repair before we leave.
Tools & methods
Tools and methods we use on your soffit and fascia
Fascia tools are for cutting and fitting timber — the saw, the primer and the paint, in that order.
Circular saw and pry bar
Cuts out the rotted board and lifts it without damaging the good timber around it, so the repair is clean and the new board fits.
New timber and primer
Replaces the rotted board with new timber, primed and painted, so the repair lasts and the paint holds.
Moisture meter
Finds the wet timber the leak has caused, so the repair covers the rot, not just the board that shows it.
Ladder and stabiliser
Gets the crew to the eave safely, with the ladder held off the gutter so the run is not bent by the climb.
Sealant and paint
Seals the joints where the detail calls for it, and finishes the new timber so the repair looks like it was always there.
Soffit vent covers
Fits vent covers that keep insects out of the attic while letting the air in, so the intake stays open and the attic stays dry.
Use cases
When Dallas homeowners call us for fascia and soffit
These examples show how a fascia and soffit repair is scoped to the rot — and the gutter that caused it.

Fascia rot in Oak Cliff
A 1920s bungalow where the fascia had rotted at the corners, and the gutters were pulling away from the house. The rotted sections were replaced, the gutters were re-hung to the new fascia, and the corners were sealed.
Soffit vents in North Dallas
A two-story home where the soffit vents had been painted shut years ago, starving the attic of intake. The vents were opened and cleared, the baffles were checked, and the air began to move again.
Problems we solve
Problems soffit and fascia repair solves for Dallas homes
Most soffit and fascia calls are one of these four. Each one starts with the same question: how much board is rotted?
Fascia rotting behind the gutter
We cut out the rotted board and replace it with new timber, primed and painted, and fix the gutter that kept it wet.
Gutters pulling away from the house
A gutter hung to a rotted fascia will pull away. We repair the fascia first, then re-hang the gutters to the new board.
Soffit sagging or stained
A sagging soffit is a sign of rot or water behind it. We open the soffit, find the wet timber, and replace what is rotted.
Soffit vents painted shut
Vents that are painted shut starve the attic of intake. We open the vents and check the baffles, so the air can move.
Cost factors
What shapes the cost of soffit and fascia repair in Dallas
HOW MUCH BOARD IS ROTTED, AND WHAT HUNG FROM IT
Length of the rot
A short section of fascia is a small job. A full run of fascia and soffit, rotted along its length, is a bigger one.
Gutters to re-hang
Gutters hang from the fascia, and when the fascia is replaced the gutters are re-hung to the new board. The re-hang is part of the scope.
Soffit vents
If the soffit vents are painted shut or blocked, opening them is part of the job. An attic with no intake bakes, and the repair should not leave it that way.
Customer reviews
What Dallas customers say
“I hired a roofing and exterior crew to replace the fascia, corner trim, gutters, and the front siding on my home. The work turned out excellent, and the whole project was handled with real care.”
Why does fascia rot in Dallas?
Fascia rots when it stays wet — from a gutter that overflows, a roof edge that leaks, or a drip edge that is missing. The repair is to cut out the rotted board and replace it with new timber, primed and painted, and to fix the gutter or the roof edge that kept it wet. A fascia that is painted over without cutting out the rot will rot again.
How much does soffit and fascia repair cost in Dallas?
It depends on how much board is rotted, whether the gutters need re-hanging, and whether the soffit needs work too. A short section of fascia is a small job; a full run of fascia and soffit is a bigger one. We inspect first and give you an itemised written quote for the repair as scoped.
Can you repair fascia and gutters together?
Yes. Gutters hang from the fascia, and a soft or rotted fascia cannot hold them. The fascia is repaired first, the gutters are re-hung to the new fascia, and the soffit vents are opened so the air can move. A gutter hung to a bad board will pull away again.
What does the soffit do?
Soffit is the underside of the eave, and it carries the intake vents that let air into the attic. When the soffit vents are painted shut or blocked, the attic starves for intake, and the roof bakes. The repair opens the vents and checks the baffles, so the air can move.
Ready when you are
Get your soffit and fascia repair Dallas TX quote
An inspection, photos, and an itemised written quote for the soffit and fascia repair as scoped. Call (469) 960-7533 and tell us what your eaves are doing.

Talk with the local team
Request Soffit and Fascia Repair
Call us at (469) 960-7533 or send a message and we will get back to you. We are open 24 hours, every day. Tell us what the eaves are doing — rotting, sagging, pulling away — and we will give you a straight answer on what they need.




